Early morning meet up spot outside main street Patagonia. (Fuji x100s)
It’s about time I made it on the now popular via ferrata that straddles the back of Telluride’s box canyon. This route has been around for a long time but has grown in popularity as more via ferrata routes round the state (Ouray, Arapahoe Basin, etc.) and country are being installed. While these “iron trials” are relatively new in the states these routes comprised of metal steps, rails, and bolted cables are common in the European alps as a cross somewhere between rock climbing and scrambling. The idea is to have a fully protected route (or in the case of Telluride’s partially protected) that incorporates technical mountaineering skills and exposure that a hiking trail wouldn’t otherwise have.
As you may have gathered this was my first time clipping into the cables of a via ferrata and I’d argue that Telluride may offer one of the most stunning views so I felt like I had to share my experience for anyone who maybe interested in doing it. While you may not want to just walk up and do one of these things it is really meant to be accessible to most. In other words if you are comfortable with heights and are a hiker wanting to gain some crazy exposure then this is the trip for you and it won’t be a back breaking all day affair either! Just make sure you have the right gear. I’ll explain our experience so as to offer some local advice and cautions:
After hastily planning the day before, we met in front of the main street Patagonia store at 5:15 am just as the sun started to lighten the sky that morning. Piling into my land cruiser we headed down main street to drive up past Bridal Veil Falls on the lower switchbacks of Black Bear Pass (where there’s still two-way traffic permitted) to park at the via “trailhead” one turn from the falls pullout. After gearing up we headed up into the via ferrata and went out and back so as to get open our shop by 10:00am. This trail is technically one way so unless you’re the only group on the trail (we were) abide by the rules of the local guides, more information here.
Telluride’s via ferrata is known for its not entirely protected route with high exposure, loose single track downhill to cliff areas (no fall zones), and areas with climbers below. There are multiple places where some may want to clip in but there won’t be a place for it, test areas, there are two near the beginning of the trail that will filter out the people who may not want to continue. There is no easing into this trail but you’ll know if it’s for you early on. This via ferrata takes at most 3 hours but most could probably finish in about an hour in a half. Once you’re done with the ferrata you will need to hike back up the road to the car to get back.
Heading up the loose rocky switchbacks up to the first cable section. (Fuji x100s)
Looking back over at Black Bear Pass and my land cruiser parked at the “trailhead” from the first clip in point. (Fuji X100s)
There were only the three of us on this trip which made things very easy. The first person was Scott who is the local knowledge and guide in town and Erika, my boss and general outdoorsy person. They both had experience (and gear) that made me feel better on my first time out there.
Via ferratas are quite simple as all you need is a helmet, climbing harness, and some kind of leash or teather. Ideally the tether is shock absorbing with two locking carabiners (Petzl Scorpio Vertigo, below) or some places allow dynamic rope and wire carabiners (Scott’s set up to the right). Either way the two clips allow for a redundant system so that you can be secured to the cable at all times. Falls can happen but they should always be avoided if at all possible as this is afterall just protection not intended to be used. The advantage to having a designed tether is the shock absorber that would protect your body, in the case of a fall, from shock load which could be fatal. So if you are worried buy an approved tether or just make sure not to fall ; ).
Scott at the bench getting ready for the “main event” (Fuji x100s)
Petzl Scorpio Vertigo with locking carabiners, elastic leashes, and shock absorber. (Fuji X100s)
While this trip went quickly it was an absolute blast to start the morning on iron ladders with friends. If I could give any advice it would be to do it in the morning to see the light hit the peaks and to avoid windy weather. You also really don’t need a whole lot of other gear a backpack with more than water and snack is definitely not needed.
